Hi Bastian,

The problem is that the compile pre-processing in the UtFFT module is
not correctly set up.  At present it requires the fftw3 package
(development package) to be installed, but it should use the native DSAM
FFT code in this case.  I will have a look at this bug.

In the mean time this problem could be quickly resolved by installing
the fftw3 development package then re-doing "./configure".

Many regards,


...Lowel.


On Mon, 2010-07-19 at 14:56 +0200, Bastian Epp wrote:
> Hi List!
> 
> (In case somebody else encounters this problem I write to the whole list 
> rather than contacting Lowel directly):
> 
> I just downloaded DSAM (latest version - 2828) and tried to install it. 
> However I failed. (argh).
> 
> When I run
> 
> ./configure
> 
> things look fine...no errors, no warnings. However: when runnig 
> configure the first time, some 'chmod'-commands seem to fail due to the 
> absence of certain folders:
> 
> --------------
> chmod: cannot access `dsam-config': No such file or directory
> config.status: creating CfgTools/Makefile
> chmod: cannot access `dsam-config': No such file or directory
> config.status: creating Makefile
> chmod: cannot access `dsam-config': No such file or directory
> config.status: creating Include/Makefile
> chmod: cannot access `dsam-config': No such file or directory
> config.status: creating src/Makefile
> chmod: cannot access `dsam-config': No such file or directory
> config.status: creating src/MainLib/Makefile
> chmod: cannot access `dsam-config': No such file or directory
> config.status: creating src/StdLib/Makefile
> chmod: cannot access `dsam-config': No such file or directory
> config.status: creating src/ExtLib/Makefile
> chmod: cannot access `dsam-config': No such file or directory
> config.status: creating src/GrLib/Makefile
> chmod: cannot access `dsam-config': No such file or directory
> config.status: creating src/GrLib/Bitmaps/Makefile
> chmod: cannot access `dsam-config': No such file or directory
> config.status: creating ModuleSpecs/Makefile
> chmod: cannot access `dsam-config': No such file or directory
> config.status: creating Examples/Makefile
> chmod: cannot access `dsam-config': No such file or directory
> -------------
> 
> well...that can be helped (Q&D) by running configure again. Fine. But 
> when running
> 
> make
> 
> things stop with an error message:
> 
> ----------------
> In file included from UtFFT.c:43:
> ../../Include/UtFFT.h:96: error: expected ‘)’ before ‘fTInv’
> UtFFT.c:365: error: expected ‘)’ before ‘fTInv’
> make[4]: *** [UtFFT.lo] Fehler 1
> make[4]: Leaving directory 
> `/home/bastian/downloads/DSAM/dsam2828/src/MainLib'
> make[3]: *** [all] Fehler 2
> make[3]: Leaving directory 
> `/home/bastian/downloads/DSAM/dsam2828/src/MainLib'
> make[2]: *** [all-recursive] Fehler 1
> make[2]: Leaving directory `/home/bastian/downloads/DSAM/dsam2828/src'
> make[1]: *** [all-recursive] Fehler 1
> make[1]: Leaving directory `/home/bastian/downloads/DSAM/dsam2828'
> ----------------
> 
> 
> I checked the source code, and of course that is fine...
> 
> I run:
> 
> Debian Linux (Lenny)
> 2.6.26-2-686-bigmem
> 
> ....any ideas?
> 
> THX in advance and all the best from Oldenburg!
> 
> BAstian