Hi,
I've downloaded a new version, but the problem persisted.
I found that I didn't have any *.mexmaci64 files in my toolboxes...
Fortunately, I found those here (in case anyone has the same issue).
https://w3.rcc.uchicago.edu/redmine/projects/cacioppo/repository/revisions/9/show/spm8_dev/toolbox/DARTEL
Best regards,
ines
On Fri, May 16, 2014 at 12:19 PM, John Ashburner <[log in to unmask]> wrote:
> I guess you are using spm8. Do you have the latest updates of spm8
> installed? I don't remember when we first released mex files for 64 bit
> Macs, but it may be possible that the version that you have does not include
> the toolbox/DARTEL/optimNn.mexmaci64 file.
>
> Best regards,
> -John
>
>
>
> On 15 May 2014 16:44, InĂªs Violante <[log in to unmask]> wrote:
>>
>> Hi,
>>
>> I am having the same issue and all the files are in the directories
>>
>> Running 'VBM8: Estimate & Write'
>> Initial Coarse Affine Registration..
>> Fine Affine Registration..
>> Failed 'VBM8: Estimate & Write'
>> Error using ==> optimNn at 68
>> Not compiled for MACI64 in MATLAB 7.11.0.584 (R2010b) (see make.m)
>>
>> In file "/Applications/spm8/toolbox/DARTEL/optimNn.m" (v1143),
>> function "optimNn" at line 68.
>> In file "/Applications/spm8/toolbox/Seg/spm_preproc8.m" (v4148),
>> function "spm_preproc8" at line 818.
>> In file "/Applications/spm8/toolbox/vbm8/cg_vbm8_run.m" (v411),
>> function "run_job" at line 206.
>> In file "/Applications/spm8/toolbox/vbm8/cg_vbm8_run.m" (v411),
>> function "cg_vbm8_run" at line 96.
>>
>> The following modules did not run:
>> Failed: VBM8: Estimate & Write
>>
>> Any suggestions?
>>
>> Thanks a lot,
>>
>> Ines
>>
>> On Tue, Nov 12, 2013 at 5:07 PM, John Ashburner <[log in to unmask]>
>> wrote:
>> > SPM is expecting to find a file called
>> > /home/amministratore/Desktop/Toolbox
>> > Matlab/spm8/toolbox/DARTEL/optimNn.mexa64 . Check to make sure that
>> > this
>> > file exists. If your installation worked properly, this file should
>> > have
>> > been among the original SPM8 distribution, over which you installed the
>> > updates.
>> >
>> > Best regards,
>> > -John
>> >
>> >
>> >
>> > On 12 November 2013 16:34, Giulio Pergola <[log in to unmask]>
>> > wrote:
>> >>
>> >> Dear SPM list,
>> >>
>> >> I am using "New segment" on a UNIX system with the latest MATLAB
>> >> release
>> >> (8.2.0.701 2013b) installed. The procedure fails shortly after
>> >> beginning
>> >> with an error log that I've seen also in the archives with previous
>> >> matlab
>> >> releases (see below). I tried updating SPM with the latest updates
>> >> available
>> >> (Feb 2013), but it still does not work.
>> >>
>> >> Any suggestions?
>> >>
>> >> Best,
>> >>
>> >> Giulio
>> >>
>> >>
>> >> Running 'New Segment'
>> >> Failed 'New Segment'
>> >> Error using optimNn (line 68)
>> >> Not compiled for GLNXA64 in MATLAB 8.2.0.701 (R2013b) (see make.m)
>> >>
>> >> In file "/home/amministratore/Desktop/Toolbox
>> >> Matlab/spm8/toolbox/DARTEL/optimNn.m" (v1143), function "optimNn" at
>> >> line
>> >> 68.
>> >> In file "/home/amministratore/Desktop/Toolbox
>> >> Matlab/spm8/toolbox/Seg/spm_preproc8.m" (v4148), function
>> >> "spm_preproc8" at
>> >> line 818.
>> >> In file "/home/amministratore/Desktop/Toolbox
>> >> Matlab/spm8/toolbox/Seg/spm_preproc_run.m" (v4677), function "run_job"
>> >> at
>> >> line 106.
>> >> In file "/home/amministratore/Desktop/Toolbox
>> >> Matlab/spm8/toolbox/Seg/spm_preproc_run.m" (v4677), function
>> >> "spm_preproc_run" at line 30.
>> >> In file "/home/amministratore/Desktop/Toolbox
>> >> Matlab/spm8/toolbox/Seg/tbx_cfg_preproc8.m" (v4337), function
>> >> "spm_local_preproc_run" at line 363.
>> >>
>> >>
>> >
>
>
|