Print

Print


HI John

Visit a picture framer and ask about 'non reflective perspex' - it has a non-reflective coating on one side so, er , it doesn't reflect as much light as ordinary gall or perspex does, and being plastic its light and much harder to break than glass. You only need a piece about two or three mm thick, so the weight will be minimal.

If at all possible avoid using the camera flash to light the subject, as this will maximise the amount of reflected light directed back at the lens.

Hope this helps

Good luck

Richard.


Richard Ellam
L M Interactive
Science Shows and Hands-On Stuff




On 23 Jun 2011, at 19:44, John Bibby wrote:

Can anyone advise please on a good way of photographing documents?

I have in mind using a tripod facing down to a horizontal surface.

But how to keep pages flat? Glass is heavy, reflective, dangerous and fragile - what is the best alternative?



And what about transparencies and negatives?

(The reason I am not using a scanner is that this work has to be done in the library; also, photography is so much quicker than scanning.)


Thanks for  advice that anyone can give.

JOHN BIBBY





********************************************************************** Further information about the psci-com discussion list, including list archive, can be found at the list web site: http://www.jiscmail.ac.uk/lists/psci-com.html You may also change your settings and subscribe/unsubscribe to psci-com from the web site.

Psci-com is part of the National Academic Mailing List Service, known as 'JISCMail'. It adheres to the JISCMail Acceptible Use Policy: http://www.jiscmail.ac.uk/policyandsecurity/acceptableuse.html and to the JISCMail guidelines for etiquette: http://www.jiscmail.ac.uk/policyandsecurity/etiquette.html

Email commands: 1. To suspend yourself from the list, whilst on leave, for example, send an email to mailto:[log in to unmask] with the following message:

set psci-com nomail -- [include hyphens]

2. To resume email from the list, send an email to [log in to unmask] with the message:

set psci-com mail -- [include hyphens]

3. To leave psci-com, send an email to [log in to unmask] with the message:

leave psci-com -- [include hyphens]

Please allow up to 24 hours for these commands to activate. Remember that you will need to send commands using the same email address that you used to register on psci-com. To contact the Psci-com list owner, please send an email to: [log in to unmask]

**********************************************************************


********************************************************************** Further information about the psci-com discussion list, including list archive, can be found at the list web site: http://www.jiscmail.ac.uk/lists/psci-com.html You may also change your settings and subscribe/unsubscribe to psci-com from the web site.

Psci-com is part of the National Academic Mailing List Service, known as 'JISCMail'. It adheres to the JISCMail Acceptible Use Policy: http://www.jiscmail.ac.uk/policyandsecurity/acceptableuse.html and to the JISCMail guidelines for etiquette: http://www.jiscmail.ac.uk/policyandsecurity/etiquette.html

Email commands: 1. To suspend yourself from the list, whilst on leave, for example, send an email to mailto:[log in to unmask] with the following message:

set psci-com nomail -- [include hyphens]

2. To resume email from the list, send an email to [log in to unmask] with the message:

set psci-com mail -- [include hyphens]

3. To leave psci-com, send an email to [log in to unmask] with the message:

leave psci-com -- [include hyphens]

Please allow up to 24 hours for these commands to activate. Remember that you will need to send commands using the same email address that you used to register on psci-com. To contact the Psci-com list owner, please send an email to: [log in to unmask]

**********************************************************************