We have used the PEI precipitation described by Pavan, very high salt (2M or even higher) as alluded to by Ana, or heparin columns with success. In some cases, a denaturing purification protocol can be very useful, but of course this assumes you can refold the protein. In the case of a student whose thesis committee I am on, the RNase and DNase has not worked, maybe because the NAcid is protected by being bound to the protein, although I know others have used it with success. For that student, the ONLY thing that worked was PEI.
Jeff
_______________________________________
Jeffrey S. Kieft, Ph.D.
Assistant Professor
Dept. of Biochemistry and Molecular Genetics
University of Colorado School of Medicine
http://www.uchsc.edu/sm/bbgn/kieftj.htm
http://www.evolutionarygenomics.com/CERT/CERT.html
_____________________________________
For mail:
UCHSC at Fitzsimons
Mail Stop 8101, PO Box 6511
Aurora, CO 80045
For courier/packages:
South Building RC-1, Room 9110
12801 East 17th Ave.
Aurora, CO 80010
phone: 303-724-3257
fax: 303-724-3215
email: [log in to unmask]
"Open your eyes. You have only to see things clearly, to understand."
-Leonardo da Vinci
-----Original Message-----
From: CCP4 bulletin board [mailto:[log in to unmask]] On Behalf Of William Scott
Sent: Thursday, July 05, 2007 8:04 AM
To: [log in to unmask]
Subject: Re: [ccp4bb] How to remove nucleic acid contamination for crystallizing zinc finger protein
It can also ppt out your protein, if it is bound to the DNA.
You could also DNase and RNase the bejesus out of it, and temporarily
unfold the protein to aid in release of the nucleic acids. Then you need
to get rid of these evil enzymes before you put back your nucleic acid of
choice.
Pavan wrote:
> You could also try polyethyleneimine (Polymin P) precipitation to
> precipitate out your DNA. Add Polymin P dropwise to a final
> concentration of 0.24% to your cell lysate while stirring in the cold
> for an hour. This should precipitate out your DNA. Then centrifuge
> your lysate and use the relevant fraction (supernatant or pellet) for
> further purification.
>
> Pavan
>
> On 7/5/07, Ana Silva <[log in to unmask]> wrote:
>> Hi,
>>
>> How much salt do you have in your protein buffer?
>> I would try to increase the salt concetration, during purification.
>>
>> Hope it helps.
>> Ana
>>
>>
>>
>> [log in to unmask] wrote:
>> >
>> > Dear all,
>> >
>> > Sorry for the off-topic question.
>> >
>> > I am purifying a zinc finger transcription factor for crystallization.
>> > The protein appeared as a single band on SDS-PAGE (MW 44KD) after NTA
>> > chelating column, but its OD280/OD260 ratio is as high as 1.0. So I
>> > doubt the protein is nucleic acid contaminated, probably because of
>> > the zinc finger. I tried to remove the nucleic acid by Mono Q and
>> > Superdex 75 pg, but failed. So could any one recommend some method to
>> > remove the nucleic acid during protein crystallization, esp. zinc
>> > finger protein? Any experience or references will be appreciated.
>> >
>> > Thanks a lot!
>> >
>> > Tiancen Hu
>> >
>> > Shanghai Institute of Materia Medica
>> >
>> >
>> >
>> > ------------------------------------------------------------------------
>> > 一起 来,150 万 人 同 时 在 玩 的 梦 幻 西 游
>> > <http://event.mail.163.com/chanel/xyq.htm?from=126_NO4>
>>
>
>
> --
> Pavan
> http://umsis.miami.edu/~pvaidyan
>
|