The devices designed to stop a non-rotative beam engine from destroying
itself seem to go back almost to the earliest days of the beam engine.
The two components that normally appear on these engines were the catch
wing, mounted above the beam with a fixed above the beam, usually to a pin
pretty much in line with the centre line of the piston rod.
The spring beams were made of large baulks of timber designed to stop the
engine coming too far in-doors and smashing the bottom out of the cylinder.
Generally, but not always, a similar arrangement was provided on the
outdoors (pump end) end of the beam to stop the piston coming through the
top of the cylinder, or damage to the pumps.
Usually a replaceable piece of timber was attached to the top of the spring
beam to take the brunt of the strike from the catch wing. Sometimes
India-rubber was used instead as can be seen on at least one of the engines
at Crofton. Close examination of most of the surviving non-rotative engines
will show marks indicating that the spring beams would e stuck fairly often.
This would occur either during starting when the engine would be worked by
hand, or during a mechanical failure when something broke.
In some cases additional equipment was added to the plug-rod operated valve
gear to provide additional means of stopping the engine should a over-stroke
occur.
Paul Stephens
IT Manager
David S Smith Corrugated Bristol
David S Smith Corrugated Bristol
First Avenue, Portbury Way,
Portbury, Bristol, BS20 7XR
Tel: +44 (0) 1275 551023 (Direct)
+44 (0) 1275 375311 (Switchboard)
Fax: +44 (0) 1275 374939
-----Original Message-----
From: Newman, Phil [mailto:[log in to unmask]]
Sent: Monday, September 01, 2003 08:57
Subject: Re: Spring beams
Thanks Andrew, now I understand what they're for but where exactly were the
cross arms or arch heads located? Were they fixed to the beam? On the famous
Perran Foundry cross section for example (printed in Barton and elewhere)
the cylinder end of the beam on the in-house stroke is below the top of the
spring beam. Is the cross arm not shown on this drawing?
Thanks for your help
Phil Newman
-----Original Message-----
From: Andrew Hurrell [mailto:[log in to unmask]]
Sent: Friday, August 29, 2003 6:54 PM
To: [log in to unmask]
Subject: Re: Spring beams
The spring beams on a non-rotary beam engine are there to act as a buffer.
If the engine hits the bottom of the cylinder on the 'in-house' stroke or
the top of the cylinder (and bottom of the pumps) on the 'Out of House'
stroke there is a good chance that the engine will smash the cylinder
casting. This could be because of something like a pump rod breaking or the
valve gear not operating properly.
Cross arms ('Arch Heads' ?) raised above the ends of the beams line up with
the spring beams. When the engine is working correctly, the arch heads
should stop just short of the spring beams.
The Dorothea engine, because the pump rods are missing, is sat on the spring
beams inside the engine house. The beams in this case start under the
bearings and can clearly be seen to be smaller than the structural beams
below.
Regards
Andrew
----- Original Message -----
From: "Newman, Phil" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Friday, August 29, 2003 11:10 AM
Subject: Spring beams
> Dear list,
>
> Could someone please provide a concise definition of a Spring Beam. Most
> diagrams of engine houses in the usual sources show them and the sockets
are
> usually quite evident in the structures but there precise function is not
> fully clear to me.
>
> Thanks in anticipation
>
> Phil Newman
>
This e-mail is intended solely for the person to whom it is addressed and may contain confidential or privileged information. If you have received in error please notify us immediately and destroy this e-mail and any attachments. In addition you must not disclose, copy, distribute or take any action in reliance on this e-mail or any attachments.
Any views or opinions presented in this e-mail are solely of the author and do not necessarily represent those of the company. E-mail may be susceptible to data corruption, interception, unauthorised amendment, viruses and delays or the consequences thereof. Accordingly, this e-mail and any attachments are opened at your risk.
DS Smith (UK) Limited, registered in England No. 501594, registered office 4-16 Artillery Row, London SW1P 1RZ
|